PlaneSpottingWorld welcomes all new members! Please gives your ideas at the Terminal.

Martin-Baker MB 2

From PlaneSpottingWorld, for aviation fans everywhere
MB2
Martin-Baker MB2 during testing
Type Fighter
Manufacturer Martin-Baker
Designed by James Martin
Maiden flight 3 August 1938
Status Experimental
Number built 1
Developed from Martin-Baker MB1

The Martin-Baker MB2 was a British private-venture fighter prototype based on a simple basic structure that had been developed in the earlier MB1 civil aircraft. Although briefly evaluated as a fighter by the Royal Air Force, the MB2 was limited in design potential and never entered series production.

Design and development

James Martin, broadly responding to Specification F.5/34, designed a fighter utilising the simple basic structure employed and developed in his earlier MB1. Constructed of steel tubing, the MB2 incorporated many detailed improvements which further simplified production as well as repair and maintenance. Powered by a special Napier Dagger III HIM 24-cylinder H-type engine of 805 nominal bhp, but capable of operation at 13 lb boost to give over 1,000 hp for takeoff, driving a fixed-pitch, two-blade propeller, the MB2 was capable of 300+ mph speeds "on paper." The undercarriage was fixed but cleanly faired in two trouser-type fairings, the port one carrying the oil-cooler. A retractable undercarriage to improve performance was "in the works" when the design was abandoned.

The fuselage lines were square cut and exceptionally clean, with almost constant depth from nose to tail. An unusual feature, at that time, was that the fuselage was slightly longer than the span of 34ft 6in, a feature retained in later Martin-Baker designs, which contributed to good stability and control in yaw. The MB2 was the first British fighter to carrying eight wing-mounted Browning .303 (7.7mm) machineguns.

One of the hallmarks of Martin-Baker designs was the simple but efficient installation of main systems. The clean and orderly cockpit was set well back, allowing a good view downwards behind the wing. A crash post was fitted, which automatically extended to minimise structure damage and injury to the pilot in the event of a nose-over landing. A small, tapered tailplane was mounted on the top of the fuselage well forward of the stern post, while the fin and rudder combination was roughly triangular in side elevation. This arrangement placed most of the effective rudder area below the tailplane, thus providing an adequate balance to the keel surface and assuring good recovery from spins. In initial MB2 configurations, there was no fin and the rudder was mounted on the fuselage but lateral stability was unsatisfactory, with the fixed fin added later.

Testing and evaluation

The MB2 was first flown by Captain Valentine Baker at Harwell on 3 August 1938 and initially tested with markings M-B-1 (G-AEZD not carried). "The Aeroplane" stated, "in spite of its fixed undercarriage, the MB2 had a performance as good as that of contemporary fighters and a capacity for quick and cheap production by the simplicity of its structure and easy assembly". Repair and maintenance were also simple[1], and these factors might have influenced the authorities towards putting the MB2 into production when the country's fighter strength was disproportionately low.

The MB.2 was subsequently acquired by the Air Ministry in June 1939 as P9594 and returned to A&AEE for a second assessment after modifications were made to tail control surfaces. The MB2 also spent some time at the AFDU, Northolt, before returning to Martin-Baker late in 1939, where it still survived in December 1941, although probably flown little or not at all after the outbreak of war.

Around this time Martin was considering various other ideas, both for complete aircraft and for certain components. The aircraft designs included a twin-engined 12-gun fighter and a twin-engined multi-seat transport, both featuring the finless layout of the early MB2 airframe. In the fighter design, the trailing edge of the engine nacelles provided additional vertical control surfaces, and also incorporated the patented ducting system evolved by Martin to reduce drag caused by the engine exhaust. The most promising of the concepts became the MB3 which would eventually spawn the superlative MB 5 prototype.

Specifications (MB 2)

Data from The British Fighter since 1912 [2]

General characteristics

  • Crew: One
  • Length: 34 ft 9 in (10.59 m)
  • Wingspan: 34 ft 0 in (10.37 m)
  • Height: 9 ft 9 in [3] (2.97 m)
  • Wing area: 212 ft² (19.7 m²)
  • Loaded weight: 5,537 lb (2,517 kg)
  • Powerplant:Napier Dagger III 24-cylinder air-cooled H-type piston engine, 1,000 hp (746 kW)
  • Propellers: Two blade wooden prop, 1 per engine
    • Propeller diameter: 10 ft 6 in (3.20 m)

Performance

Armament


References

Notes

  1. Bowyer 1984, p. 35.
  2. Mason 1992, p.266.
  3. Green and Swanborough 1994, p.362

Bibliography

  • Bowyer, Michael J.F. Interceptor Fighters for the Royal Air Force, 1935-45. Wellingborough, UK: Patrick Stephens Ltd., 1984. ISBN 0-85059-726-9.
  • Bridgman, Leonard (ed.). “The Martin-Baker F.18/39.” Jane’s Fighting Aircraft of World War II. London: Studio, 1946. ISBN 1-85170-493-0.
  • Green, William and Swanborough, Gordon. The Complete Book of Fighters. New York: Smithmark, 1994. ISBN 0-8317-3939-8.
  • Mason, Francis K. The British Fighter since 1912. Annapolis, Maryland:Naval Institute Press, 1992. ISBN 1-55750-082-7.

External links

See also

Related development

Comparable aircraft

Designation sequence


This article is licensed under the GNU Free Documentation License.
It uses material from the Wikipedia article "Martin-Baker MB 2".